Travertine Tile Glossary
A
Abrasion Resistance
This refers to the resistance of a flooring surface when exposed to continuous contact of an abrasive material or consistent friction.
Abrasive Finish
This indicate a nonreflective or flat surface finish.
Abrasive Hardness (HA)
HA is a measurement of how a stone wears when subjected to abrasion.
Absorbed Moisture
Solid material absorbs moisture.
Absorption
Absorption is the relationship of the weight of the water to the subject.
Accelerator
This is a substance that is added to mortar, grout, or concrete in order to increase the rate of hardening. Furthermore, it reduces the time needed for the substance to firm.
Acid Wash
This treatment is applied to stone in order to reduce the shine of the surface area and create a more rustic appearance.
Acid/Acidic
Acid has a pH rating which falls below 7.
Acrylic Resin/Plastics
This resin is transparent and resistant to contaminants.
Adhered
The term describes the stone being secured and supported onto an approved backing by an approved bonding agent.
Adhesion
An adhesive is used to hold together two surfaces.
Adhesion Mechanical
Adhesion of two surfaces by interlocking action.
Adhesive
A glue is a substance that bonds two materials to one another.
Admixture
This term defines a substance that may be added to concrete at the installation site.
Agglomerated Stone
This describes a man-made substance comprised of resin combined with crushed stone.
Air-entraining
The developing of air bubbles during the mixing of mortar, cement, or concrete.
Air-entrainment
The locking in of air, in the form of tiny bubble, when concrete or mortar is mixed (see also Air-entraining and Entrained air).
Alkali
Alkali is a chemical that neutralized acidic material.
Alabaster
Alabaster describes a category of gypsum that has a fine grain. The term is often incorrectly applied to marble with a fine grain.
Alkaline
This is a base chemical substance (for example carbonate of sodium or potassium). This substance is used to neutralize acidic substances.
Antique Finish
Antique finish is created by chemical or mechanical means in order to achieve a rustic or distressed finish.
Apron
This is a piece of trim located under the top of a piece of projected stone.
ASI (Allied Stone Industries)
The Allied Stone Industries is constituted of stone quarries and fabricators.
B
Back-buttering
Applying a layer of adhesive (for example glue), to the back of a stone tile before installation. This ensures the proper coverage of mortar and prevents future tile bursting.
Backing Rod
This is a flexible material (for example butyl rubber or polyethylene) installed at the rear or bottom of a joint.
Backsplash
Backsplash is a section of wall generally located above a counter and below a cabinet. It typically has 16-18 inches in height.
Base
The vertical first member over the grade of a completed floor, or the bottom of a stone wall.
Bed Joint
A horizontal joint in stonework, generally filled with sealant or mortar.
Belt Course
The continuous horizontal course that marks a rupture in the plane of the wall.
Bevel
A sloped surface that follows a horizontal or vertical surface.
Bleed
Staining on a stone surface caused by caulking, oil-based putties, sealing compounds, or corrosive metals.
Blending
Positioning adjacent floor slabs, tiles, stone, or veneer panels properly by color.
Block Cutter
A block cutter is a machine used during quarrying to drill small diameter holes.
Bond
To adhere.
Bonding Agent
This term describes a substance that may be applied to a material in order to create a bond between that material and a subsequent layer.
Book Match Pattern
Laying out the stone elements of a design in order to ensure the patterns match.
Bowing
This is a curving, or warping of the wall cladding.
Brick Trowel
Brick Trowel is mainly used on brick but is also popular in the 5″ x 11″ size for terra cotta and quarry tile work.
Brushed Finish
A finishing technique that requires the stone be brushed by a coarse wire brush. This replicates the appearance of natural wear over time.
BSI (Building Stone Institute)
The Building Stone Institute is a trade association of fabricators, quarries, dealers, which was founded in 1919. BSI works with natural stone.
Bull Float
A tool used to smooth the surfaces of unformed freshly poured concrete. The tool usually measures 8″x 42″-62″ and is made of wood, magnesium, or aluminum.
Bullnose
The convex rounding of a section of stone trim. Usually used on edges (for example the front of stairs).
Bullnose Tile
Stone tile that has a bullnose edge built in, also known as a cap.
Bush Hammering
Those are textured surfaces which vary from subtle to rough, created by a mechanical process.
Butt Joint
A square joint between two members.
Buttering
Buttering is a method of spreading a coating of bonding material, followed by a mortar or adhesive coat.
C
Calcareous
This is a substance which consists of calcium carbonate.
Calcite
Calcite is a type of limestone with crystalline qualities. It doesn’t contain more than 5% magnesium carbonate.
Calcite Streaks
A milky streak found within stone made when a small crack is filled with a deposit of calcium.
Calibration
This is the first step in finishing a stone tile. Abrasive pads are applied to the face of the stone at high speed and extreme pressure and this allows the stone to be ground into a consistent thickness, which is necessary for tile installation.
Calibrated
The method by which cement or stone is machined in order to create a uniform thickness.
Casing
A trim generally used around doors, entryways, or windows.
Caulking
This means sealing a joint with an adhesive.
Caulk
This is a flexible substance spread into joints to create a barrier against air and water.
Cement
An adhesive that sets by the process of a chemical reaction. Cement is often mixed with gravel, sand, and water to create concrete.
Cement Backer Unit (C.B.U.)
A material placed between cement flooring and the wooden subflooring in order to create a moisture barrier and provide support.
Cement Board
Aggregate cement panels which are reinforced on either side with a glass-fiber mesh.
Cement Grout
A mixture of cement, sand, and water that creates a uniformly colored and water resistant substance. This mixture is used to fill the joints between tile pieces.
Cement Mortar
A mixture of cement, sand, and water which is used to bond tile to a base such as a floor or wall.
Cement, Portland
A hydraulic cement created by crushing hydraulic calcium silicates which contain one or more forms of calcium sulfate as well as other additives.
Cement, White
Portland cement that hydrates to a white paste.
Chamfer
A beveled edge at the junction point created by cutting away the edge where the two surfaces meet at an external angle.
Chat Sawn Finish
A rough finish achieved by sawing with coarse abrasives
Cladding
A stone veneer used as the facing on an interior or exterior wall. It is not meant to be load bearing.
Clast
This term describes an individual grain of a rock.
Cleavage
A cleavage is a rock’s ability to break along natural surfaces.
Cleavage Plane
The planes within a stone along which the stone is most likely to break.
Chiseled Edge
This is the method which gives an aged appearance to stones.
Cleft Finish
Stones that have been separated along the natural seem.
Coefficient of Friction (C.O.F.)
C.O.F. is the ability of a surface to resist having another object slide across it.
Cobblestone
A stone which is large enough to be used in paving, usually made of granite.
Compaction
The process of reducing fresh concrete or mortar by centrifugation, vibration, tamping, or a combination of the three. Typically performed to remove voids other than intended air.
Compressive Strength
This refers to the maximum resistance of mortar or concrete to axial loading.
Condensation
Water droplets deposited on surfaces with a temperature below the dew point.
Course
The horizontal range of stone units measuring the length of a wall.
Cove
A tile trim used on baseboards and corners with one concave edge.
Cove Base
This is a stone molding that is concave in shape.
Cove Molding
A molding that is concave in shape. Usually found at the sloped junction of a ceiling and wall.
Coverage
The coverage is the amount of material needed in order to cover a surface.
Crack
This term describes a split in the surface of a floor.
Crazing
Crazing means small interconnected cracks in the surface of a finished stone product.
Cross-cut
Cutting a block of stone parallel along the naturally occurring bedding plane.
Cure
The chemical reaction achieved through heat, condensation or others by which cement, or another adhesive, reaches its maximum strength.
Cure Time
The amount of time needed for the adhesive or cement beneath the tile to set and become hard.
Curing
The process of maintaining the proper temperature and humidity around fresh concrete. This happens in order to allow it to harden properly.
Curing Blanket
Covering freshly poured concrete with matting, straw, sacks, waterproof paper, or another material.
Curing Compound
This describes a liquid applied to the surface of new concrete in order to prevent the loss of water.
Curtain Wall
A curtain wall is a stone cladding which is used to protect a building from the elements and held in place by an anchoring system.
Cut Stone
Cut stone is a finished stone ready to be put into place.
D
Damp Proofing
This describes the process of applying a water resistant compound, usually to the back of a wall or to a stone facing.
Diamond Sawed
The finish achieved by sawing a piece of stone with a diamond.
Dimension Stone
A natural stone cut and finished to manufacturer specifications.
Dolomite
Dolomite is available in numerous textures, colors and is made of a variety of limestone, crystalline in character, that contains more than 40% magnesium carbonate.
Dressing
This term is often called “scabbing”. It is a method of preparing blocks for shipment and storage.
Dry Seam
A fracture in a piece of stone that has not healed, this may indicate a plane of weakness.
Dry Set Mortar
This is a mortar made of cement and applied in a thickness of maximum 3/16″.
Ditra
Diatra (also known as an underlayment) is a substance layered and used as a foundation for tile. This protects the subfloor and also allows the tiles to move a tiny without being damaged.
E
Eased Edge
This refers to a softened square edge profile rather than the standard sharp edges.
Efflorescence
A powdery white residue, resulting from a deposit of salt, which forms on the surface of brick, stone, or mortar. This is caused by alkalis which have been leached from the masonry and brought to the surface by moisture.
Elevation
Either an exterior or interior drawing of the elements and vertical faces of a structure.
Entrained Air
Small air bubbles incorporated into concrete or mortar during the mixing process. This is usually achieved by using a surface active agent. (See also air entrainment.)
Epoxy Adhesive
An adhesive containing a hardener and epoxy resin that is used to adhere tiles to a surface beneath the tile.
Epoxy Grout
A type of grout containing a hardener and epoxy resin that is used to fill grout lines and to fill joints.
Epoxy Resin
A flexible resin, often used as an adhesive, that us is usually made by the polymerization of an epoxide.
Etched
A decorative pattern usually created by sandblasting or with an abrasive chemical.
Expansion Anchor or Bolt
The anchor, or bolt, expands as it is screwed into a drilled hole.
Expansion-Contraction Joint
A joint located between stone units which contracts or expands with structural movements or temperature changes.
Exposed Face
The visible side of any stone structure.
F
Fabricated
Manufactured stone that is ready for installation.
Fabricator
A facility that cuts and customizes stone to specific dimensions.
Face
The surface of the stone that is exposed on a structure.
Fascia
A horizontal, flat, narrow structural element such as the covering between the joint between the eaves and the top of the wall.
Field Stone
Cobbles, boulders, and other loose pieces of rock found in a quarry. They are usually irregularly shaped and rough and may be used for veneers, walkways, garden linings, or freestanding walls.
Field Tile
The tile used for the large areas of floor which are often within a border.
Filling
An expression used to describe the process of filling naturally occurring voids within a stone with synthetic resins or cements.
Fines
The small stone particles, ranging from dust to sand sized material, that result from the processing of stone.
Finish
A protective coating which is applied to the surface of flooring.
Finished Stone
Stone that has been dressed, or finished, on the surface.
Fissure
A thin, irregular opening in the face of the stone.
Flagstone
Thin, fine-grained slabs of stone typically used for paving surfaces such as patios, walks, and driveways. The stone used is often bluestone, slate, or other quartz-based stone.
Flamed Finish
A finishing technique created by applying intense heat to the surface of the stone followed by rapid cooling. This is done to create a rough textured surface.
Flat Trowel
Used with a hawk to transfer mortar from a mortarboard to a wall or other surface. Frequently used for spreading cement onto the float coat and may also be used for spreading mortar on a floor before setting tiles.
Fleuri Cut
A cut parallel to the natural bedding plane made to marble or stone.
Flexural Strength
The force required to break a material when a piece of specific thickness is bent.
Floating Floor Installation
A method of installing flooring where it is not attached to the subflooring. The wooden planks are joined together via a tongue and groove mechanism, although glue may also be used, and the wooden floor then floats above the subflooring.
Floor Tile
A tile which is durable enough to be installed in flooring that is used daily.
Frost Proof Tile
Tile flooring which is resistant to damage that results from freezing and thawing.
G
Gang Saw
Also known as a frame saw, this saw is used to cut slabs of a uniform thickness from stone blocks.
Gauged or Gauging
Measuring and grinding stone in order to ensure all pieces are of a uniform thickness.
Grain
1) The primary direction of the mineral composition in stone; also the most likely direction of cleavage. 2) A tiny particle of rock.
Grout
Mortar used to fill grout lines and joints which is available in a number of colors.
Grouting
The process of filling grout lines or joints with grout.
Grouting Float
A trowel which is used to firmly push grout into joints.
H
Honed Finish
A smooth finish that may have a matte or satin appearance. This finish is achieved by stopping one step before the end of the polishing process.
I
Igneous
A volcanic rock, such as granite, which became solid after cooling from its molten state.
Impregnation
A chemical coating that is applied to a piece of stone to prevent stains from penetrating below the surface of the stone.
Impervious Tile
Tile that is water resistant with an absorption rate of no more than 0.5%.
Initial Setting Time
The time needed for freshly mixed mortar, concrete, or cement paste to initially set.
J
Joint
The space between installed pieces of stone or between the adjoining material and the dimension stone.
Joint Compound
A compound applied to joints that creates a flawless joining of the two surfaces once it has been sanded.
Joint Filler
Placed in a joint to prevent debris from entering and to provide a base for sealants.
K
Kerf
A cut in the edge of the stone where anchors may be inserted.
Keystone
The center stone of an arch which may be embellished with carvings or sculpture.
L
Listel or Listello
A small piece of border used as decoration, typically on a wall.
L Cut
A piece of tile cut into the shape of an L.
Latex-Portland Cement Grout
Portland cement grout which has a latex additive that results in a less permeable and less rigid grout when compared to regular Portland cement grout.
Latex-Portland Cement Mortar
Portland cement with a latex additive used for bonding tile to backup material. This is less rigid than regular Portland cement mortar.
Lime
Specifically refers to calcium oxide. The term may more generally be used to refer to the various forms of quicklime, hydraulic hydrated lime, and hydrated lime.
Limestone
Composed primarily of calcite, this is a sedimentary stone which is found in a variety of colors.
M
Marble
A metamorphic stone, this limestone derivative can be polished. It can be etched and polished easily but is still quite durable.
MIA (Marble Institute of America)
An international association the members of which are made up of fabricators, producers, exporters, contractors, distributors, importers, sales agents, and those who sell services and products associated with marble.
Miter
A junction of two units at an angle that is typically 45 degrees.
Modular Ratio
The ratio of elasticity of steel to concrete.
Modulus of Deformation
Elasticity expressed by two time variables; the strain evidenced when the load is first applied and the length of time the load is sustained.
Modulus of Rigidity
The ratio of shearing stress to shearing strain; denoted by the symbol G.
Modulus of Rupture
The load capacity of a beam before a rupture will occur.
Moisture Expansion
A reaction between water, or water vapor, and a ceramic product that increases its volume. This reaction may happen over time but occurs more quickly when the product is exposed to water, or water vapor, at elevated pressures and temperatures.
Moisture Movement
1) The ability of moisture to move through a porous material. 2)The effect the movement of moisture has on volume change and efflorescence in mortar, hardened cement paste, rock, or concrete.
Moldings
A decorative trim used to cover the transition between one surface and another.
Mortar
A cement mixture that contains water, lime, and sand that is used to join masonry to another surface.
Mosaic
A pattern created with small pieces of a material, typically made of stone, tile, or glass.
Mosaic Tile
Small pieces of tile which are laid together to form designs.
Mounted Tile
Tile that has been pre-mounted by paper, mesh, resin, or another material.
M.S.D.S.
The acronym for Material Safety Data Sheet. This is a required listing of any safety precautions, hazardous ingredients, and first aid information the consumer should be aware of.
Mud
The slang term used for mortar that has been made of cement and sand.
Muriatic Acid
30% hydrochloric acid.
N
NTCA (National Tile Contractors Association)
A United States trade association whose membership is made up of contractors. Associate members are comprised of those who supply services and products to the industry.
Natural Bed
Stone set parallel to the way it was discovered in the quarry.
Natural Cleft
Stone separated at a natural seam.
Natural Stone
Stone found in nature such as marble, granite, slate, limestone, sandstone, or travertine.
Non-Slip Tile
Tile that resists having objects slide across it.
Non-staining Mortar
Mortar made of materials that will not stain and that usually have low alkali content.
Notch
A cut in the shape of a V that is made on the head or edge of a stone.
Notched Trowels
Trowels used to apply bonding materials to tile. The trowel may have square teeth or be serrated and come in various sizes. The tooth size determines the depth of the mortar.
O
Off Fall
The pieces that remain when a slab of stone has been cut. These are often used for samples or small projects.
Ogee
A reverse curved edged stone molding; convex below and concave above.
Open Time
The time during which a bond coat is able to adhere to tile and bond the tile to another substance.
Organic Adhesive
An organic material which can tire with no additional liquids or powder which cures by evaporation and is used to bond tile to hack-up material.
P
Palletizing
A method of stacking stone onto wooden pallets. This method is easily transported and typically arrives in better condition than stone that has not been put onto pallets.
Parging
Applying mortar to the face of a backup material or to the back of stone.
Patina
The changing of the texture or color of a material due to age or exposure to the elements.
Paver
A single piece of stone used as exterior paving.
Paving
Stone that is used as a surface for walkways, patios, or driveways.
pH
A system of measuring alkalinity or acidity irrespective of the alkali or acid involved; a neutral pH is 7.0.
Pilaster
A shallow column or pier projecting from a wall.
Pillowed
A tile finish that creates rounded edge which result in a pillowed look.
Pinholes
Deviations in the surface of a ceramic that resembles pin pricks.
Pitched Stone
A rough stone edge or face that has been cut with a pitching chisel.
Plucked Finish
A finish created by plucking particles out of the surface.
Pointing
The last filling and finishing of mortar joints once they have been raked out.
Polished Finish
A finish that results in a glossy surface that highlights the character and color of the stone. This finish is achieved by polishing the stone with progressively finer heads during the polishing process.
Polyethylene
A thermoplastic compound used in creating protective coatings. May also be made into sheet form and then used to protect concrete surfaces as they cure or to protect construction areas.
Porosity
The size and number of pores in stone. Granite is not porous while travertine is quite porous.
P.S.I.
An acronym for pounds per square inch, which is a unit of measurement.
Pointing Trowel
The most extensively used trowel in the tile setting industry. It is used in every phase and comes in sizes ranging from 4″ to 7″. Especially useful in straightening tiles, filling, buttering, placing mortar in small spaces, and marking floated surfaces. The end of the handle may be used to tap tiles into place that have shifted.
Q
Quarry
Where stone is extracted from the earth.
Quarry Block
A piece of stone, usually rectangular in shape, as it comes from the quarry.
Quartz
One of the hardest minerals found within stones such as granite, quartzite, and sandstone. Quartz may be transparent, colorless, or colored.
R
Random Slab
A trimmed slab that may have a varying length and width as long as it is within specified limits.
Reducer Strip/ Reducer
A molding accessory that has one tapered and one grooved edge that forms the shape of a teardrop. This is usually used on fireplaces or doorways or to divide a room.
Relief
A raised embossing or carving above a background plane.
Resin
A chemical substance used in some coating processes that is clear or translucent.
Rough Sawn
A finish that is produced by using a gang sawing process.
S
Sample
A piece of stone that shows the general color range, finish, and markings of a specific type of stone.
Sandblasted
A matte surface finish created by applying a steady flow of water and sand under pressure.
Saw-Cut Refined Finish
A matte finish created by processing the stone after the initial cote to remove the heaviest saw marks but without creating a honed finish. Granite, limestone, and marble may be purchased with this finish.
Sawed Edge
An edge that has been cleanly cut with a blade or saw.
Sawed Face
A flooring surface created by using a saw to cut the tile or slab. The texture can vary from rough to smooth and the specific texture is typically named from the type of material used in sawing such as sand, shot, or diamond.
Screed
Leveling mortar in a mortar bed by using a straightedge.
Sealer
A coat that is applied to the surface of a floor prior to the application of other coats in order to prevent subsequent coats from seeping into the flooring. May also be applied at the end of the process as a protective measure.
Sealant
An elastic adhesive compound used to seal the joints of stone veneer.
Sealing
1) The process of making a veneer joint watertight with sealant. 2) Applying a substance to limit or prevent staining.
Sedimentary
Rocks formed from sediments that have crystallized such as limestone and sandstone.
Slab
A piece of quarry block that has been cut lengthwise prior to fabrication.
Slurry
A mixture of water and any insoluble material such as clay, Portland cement, or slag.
Spacer
A small device used to evenly space tiles during installation. May be shaped as a cross, T, or Y.
Split-Faced Stone
Stone that has been removed from the quarry and cut to a specific height in large chunks and then sliced to expose the natural cleft. This creates a moderately rough texture.
Spacing Mix
A dry or damp mixture of one part extra-fine sand and one part Portland cement. Used as a filler between joints of mounted ceramic mosaic tiles to maintain an even spacing during installation.
Substrate
The surface upon which stone tile is placed.
Straight 90 Degree Edge
One of the two types of edges available for a floor tile made of natural stone. This edge creates a polished and modern look.
T
TCA (Tile Council of America)
An organizations of manufacturers who serve the ceramic tile industry. Programs promote tile use, the improvement of industry standards, the development of new installation techniques and methods, and the publication of an annual handbook. Many of these methods can also be used to set stone tile as well.
Texture
The quality of the stone surface independent of color.
Textured Finish
A rough finish on the surface of the tile.
Thermal Finish
A surface treatment created by applying intense heat flaming.
Thin Stone
Dimension stone units that are less than two inches thick.
Thin-Set Mortar
A thin layer of adhesive spread onto a surface onto which tile is laid.
Threshold
Alternatively known as a saddle, it is the flat strip of stone that is projected above the floor between the jambs of a door.
Tile
A thin stone unit of uniform size usually less than 3/4″ thick.
Tolerance
The dimensional allowance during the fabrication process.
Translucence
The ability of marble to transmit light.
Travertine
A type of limestone that is created when minerals dissolve in ground water and are then deposited on the surface. Because of its density it may also be classified as a type of marble.
Tread
A flat stone that is used as the top surface of a step.
Trim
The framing of openings on the exterior or interior of a building including picture rails, baseboards, casings, and cornices.
Tumbled Finish
A weathered finish created by tumbling stone with steel bearings, sand, or pebbles. Both limestone and marble are ideal candidates for this type of finish.
U
Unit
A piece of thin dimension or fabricated cubic stone.
Undercut
A cut that creates an overhanging part.
Unsanded Grout
A product with a Portland cement base that is mixed onsite with water and then spread over the tiled area to fill the joints with a grout float. Then a sponge is used to remove excess grout from the surface while leaving the remaining grout in the joints to cure. This process is usually used during natural stone installations because of its ability to fill small joints without scratching soft stones.
V
Vapor Barrier
A waterproof material placed under concrete floor slabs that have been placed on grade.
Vein
A layer of mineral material that differs from the surrounding formation.
Vein Cut
A cut into stone perpendicular to the bedding plane.
Read more: http://learn.thehardwoodoutlet.ca/guides-checklists/glossary/travertine-tile-glossary/#ixzz3PnFB37p9